SE708v2 Version History
Copyright © Speakerbus Technology Ltd. All Rights Reserved.
This document describes the recorded features introduced by each release. Information about each
release can be reached quickly by following the links provided.
Back to the Home Page
Version History
A bug fix release.
Features added in Version 2.901.1.0
Defects resolved in Version 2.901.1.0
- Remote SE708 No RTP Media Recording Streams on Incoming Group Calls (SB-8010)
Known Defects/Issues in Version 2.901.1.0
- If the Master appearance is missing but the Intercom appearance is present then remote Intercom-enabled units do not fall-back to use the Intercom appearance if present. (F0037496)
A re-release of version 2.900.1.0 with a bug fix.
Features added in Version 2.900.2.0
Defects resolved in Version 2.900.2.0
- Can no longer login to SSH using SBEngineer or SBRootAdmin accounts after a downgrade of code (SB-7800)
Known Defects/Issues in Version 2.900.2.0
- If the Master appearance is missing but the Intercom appearance is present then remote Intercom-enabled units do not fall-back to use the Intercom appearance if present. (F0037496)
A major release addressing identified potential vulnerabilities.
Features added in Version 2.900.1.0
- Support secure iCMS communications.
- Resolve SHA1 deprecated settings for SSH (SB-6466).
- Store passwords in /etc/shadow (SB-7279).
- Use SHA512Crypt instead of MD5 (SB-7380).
- Mitigate "TCP Sequence Number Approximation Based Denial of Service" vulnerability (SB-7418).
- Hide password when using CM SFTP commands (SB-7388).
- Remove support for SE708 v2 firmware v1 downgrade option (SB-7257).
- Ignore ICMP Timestamp Request Remote Date Disclosure (SB-7583).
- Upgrade OpenSSH to the latest released (openSSH-9.9p1) version for 7* series endpoints (SB-7686)
Defects resolved in Version 2.900.1.0
- 7xx series devices do not receive group call (any type) (SB-7109).
- CDR call clear events sent for failed clear of locked group call (SB-5861).
Known Defects/Issues in Version 2.900.1.0
- If the Master appearance is missing but the Intercom appearance is present then remote Intercom-enabled units do not fall-back to use the Intercom appearance if present. (F0037496)
Bug fix release.
Features added in Version 2.800.3.0
Defects resolved in Version 2.800.3.0
- Failing to latch a channel still starts the latch timer on SE708 (SB-6056).
- Clearing a latched channel with the "clear" key fails to stop the latch timer on iD704 & SE708 (SB-5942).
- SendLogs when SNMP is enabled may have undesired effects (SB-5863).
Known Defects/Issues in Version 2.800.3.0
- If the Master appearance is missing but the Intercom appearance is present then remote Intercom-enabled units do not fall-back to use the Intercom appearance if present. (F0037496)
Bug fix release.
Features added in Version 2.800.2.0
Defects resolved in Version 2.800.2.0
- Latched Hoot Timeout does not work properly if you have many Hoots (SB-5788).
- Incorrect Server IP port displayed at the device when default values are used (SB-5762).
Known Defects/Issues in Version 2.800.2.0
- If the Master appearance is missing but the Intercom appearance is present then remote Intercom-enabled units do not fall-back to use the Intercom appearance if present. (F0037496)
- SendLogs when SNMP is enabled may have undesired effects. (SB-5863)
Enhancements release.
Features added in Version 2.800.1.0
- Support of the SSH File Transfer Protocol (SFTP), in addition to TFTP, as an option for file transfers (SB-5033).
- Support of Latched Hoot Timeout (SB-4218).
- Update of shared libraries OpenSSL to 1.1.1u, OpenSSH to 9.3p1 (SB-5570).
- Option to perform factory reset of data (SB-3851).
- Improved reporting of 802.1X issues via SNMP.
- Improvements to security of the CM interface (SB-2960).
- Allow warning text to be displayed in an ssh/dropbear session pre-authentication banner (SB-5708).
Defects resolved in Version 2.800.1.0
- Locked Group Call volume can be adjusted in error (SB-3539).
Known Defects/Issues in Version 2.800.1.0
- If the Master appearance is missing but the Intercom appearance is present then remote Intercom-enabled units do not fall-back to use the Intercom appearance if present. (F0037496)
Bug fix release
Features added in Version 2.730.4.0
Defects resolved in Version 2.730.4.0
- Fix low speaker volume levels (SB-3031)
Known Defects/Issues in Version 2.730.4.0
- If the Master appearance is missing but the Intercom appearance is present then remote Intercom-enabled units do not fall-back to use the Intercom appearance if present. (F0037496)
Bug fix release
Features added in Version 2.730.3.0
- Added rejection message for attempt to make telephony call with no dial digits specified
- Support "North America: Phoenix" (SB-1524)
- New CM commands "defaultfactory" and "certsrequest" now available for SBEngineer
Defects resolved in Version 2.730.3.0
- User name shown as Unknown after re-seat (F0034572)
- Fix for use of intercom I/0 AppId (SB-1489)
- DHCP vendor-specific info handling (SB-1625)
- DSP Firmware upgraded to v2.731.1.0 with following enhancements:
- Fix SE708 dropping secondary recording stream to the voice recorder issues (F0039014)
- When two or more streams have the same destination IP address, the destination IP address is removed from the ARP tables
- CTI bug fixes:
- Tightened up detection of AppId specified for telephony call
- Handled call state not being removed from CTI APP caused by incoming telephony call being rejected and resumed
- Handled showing Alerting to CTI for MRD receiving a ring signal (SB-1587)
- Handled telephony AppId to be of form tnnn/0
- Fix for display of intercoms for getAppearances
- Removed master appearance from getApperances as not relevant
- Unable to abandon an alerting intercom call
- Removed ability for MRD signal when on speaker from CTI app as this does not match device operation
Known Defects/Issues in Version 2.730.3.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- If the Master appearance is missing but the Intercom appearance is present then remote Intercom-enabled units do not fall-back to use the Intercom appearance if present. (F0037496)
- Pulling the network connection from the SE708 does not change the network icon to red. (F0038681)
802.1x functionality added.
Features added in Version 2.730.2.0
- Support added for 802.1x.
- Added new factory default option. (SB-760)
Defects resolved in Version 2.730.2.0
Known Defects/Issues in Version 2.730.2.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- If the Master appearance is missing but the Intercom appearance is present then remote Intercom-enabled units do not fall-back to use the Intercom appearance if present. (F0037496)
- Pulling the network connection from the SE708 does not change the network icon to red. (F0038681)
CTI functionality added.
Features added in Version 2.730.1.0
Defects resolved in Version 2.730.1.0
- Devices not registering with iCMS when 2 default gateways are configured in a DHCP offer. (F0038657)
Known Defects/Issues in Version 2.730.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- If the Master appearance is missing but the Intercom appearance is present then remote Intercom-enabled units do not fall-back to use the Intercom appearance if present. (F0037496)
- Pulling the network connection from the SE708 does not change the network icon to red. (F0038681)
SNMP functionality change.
Features added in Version 2.720.3.0
Defects resolved in Version 2.720.3.0
- If the user logged out to fully implement a config change, the device would automatically log in once it restarted. This was not the correct behaviour and this change ensures that the device now remains logged out. (F0038592)
Known Defects/Issues in Version 2.720.3.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- If the Master appearance is missing but the Intercom appearance is present then remote Intercom-enabled units do not fall-back to use the Intercom appearance if present. (F0037496)
SNMP functionality change.
Features added in Version 2.720.2.0
- If the snmpd daemon is running and there is a change to the SNMP configuration, there is a possibility that there will not be a large enough segment of memory available to restart the daemon. To avoid this potential problem, a restart will now be required before the configuration changes are implemented.
Defects resolved in Version 2.720.2.0
- A hoot with speaker and microphone muted should not be voice recorded. However, the hoot audio is recorded after a reboot. (F0038360)
Known Defects/Issues in Version 2.720.2.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- If the Master appearance is missing but the Intercom appearance is present then remote Intercom-enabled units do not fall-back to use the Intercom appearance if present. (F0037496)
SNMP feature release.
Features added in Version 2.720.1.0
- Added extended set of defined acoustics parameter values for close-talking microphone, main speaker, and echo cancellation for loudspeaker to close-talking microphone; with a distinct set for Trader2 profile.
- Added local-dipping and paired device features.
- SNMP features added:
- Removed group trap SNMP messages and replaced with support for individual trap SNMP messages.
- Support up to 10 SNMP servers.
- Automatically send SMNP trap messages to configured SMNP server(s) on detection of state changes in iCMS, SIP or Network connections.
- Support for SNMPv3, including authentication and privacy.
- SNMP sysDescr (MIB II system description) string modified to report the Speakerbus product ID and software version number.
- Memory fragmentation measured, with a trap generated when this could cause system instability; it may not always be possible to restart SNMP after a configuration change.
Defects resolved in Version 2.720.1.0
- When updating SE708 firmware from 2.3 to 2.7 the RTP ports are not defaulted to match the current published RTP port range. (F0038426)
- SNMP IF-MIB items from SE708 which give network interface statistics are reporting 0 for all the packet and octet counts of the Ethernet interface (DSP). (F0038282)
- The MAC address of a slaved record stream will be 0 for the first 10 minutes which may result in unrouteable media (DSP). (F0038329)
- UI status reports are not generated unless previously requested via the device GUI, and may not therefore be included in a Tech Support upload. (F0038512)
- MCC not working - the Linux code receives no mcc packets though they are received by the DSPCode (DSP). (F0038514)
- Miscellaneous minor bug fixes.
Known Defects/Issues in Version 2.720.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- If the Master appearance is missing but the Intercom appearance is present then remote Intercom-enabled units do not fall-back to use the Intercom appearance if present. (F0037496)
- A hoot with speaker and microphone muted should not be voice recorded. However, the hoot audio is recorded after a reboot. (F0038360)
Feature Enhancement Release.
Features added in Version 2.710.2.0
- TFTP server port configurable.
- Change the NTP configuration to set the maximum synchronisation distance.
Defects resolved in Version 2.710.2.0
Known Defects/Issues in Version 2.710.2.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- Very rarely no audio is present on a DMVS MRD call. (F0035437)
Feature Enhancement Release.
Features added in Version 2.710.1.0
- SSH port configurable.
- DSCP value for SIP messages configurable.
- Cisco CUCM configuration retrieved via HTTP GET instead of TFTP.
- User based voice recording configuration supported.
- Voice recording configuration status icon added to status bar.
- Recording Configuration status screen added to Device Info.
Defects resolved in Version 2.710.1.0
Known Defects/Issues in Version 2.710.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- Very rarely no audio is present on a DMVS MRD call. (F0035437)
Bug fix release.
Features added in Version 2.700.1.0
- Screensaver keypress now actioned instead of being ignored.
- Add 'Press Clear to cancel' text to the UI for outgoing P2P or group call in the connecting state.
- Add 'CM list' engineering command to match other devices.
- Updated OpenSSL to version 1.0.2r from version 1.0.2j
- Updated Dropbear to version 2019.78 from version 2016.74
Defects resolved in Version 2.700.1.0
- The SE 708's acoustic shock protection configuration is not handled correctly. (F0037492)
- Downgrading v2.620.1.0 onwards via the down-arrow fails. (F0037803)
Known Defects/Issues in Version 2.700.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- Very rarely no audio is present on a DMVS MRD call. (F0035437)
Minor enhancements release.
Features added in Version 2.630.1.0
- Support for 'footswitch' operation added.
Defects resolved in Version 2.630.1.0
Known Defects/Issues in Version 2.630.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- Very rarely no audio is present on a DMVS MRD call. (F0035437)
Minor enhancements release.
Features added in Version 2.620.1.0
- Juniper Networks multicast workaround.
- Voice recorder stream duplication.
- Obsolete SPI Flash part replacement.
Defects resolved in Version 2.620.1.0
- The unit can get stuck in the 'connecting' state. (F0036553 & F0036554)
- Force iCMS listen port to 9190 if no valid value obtained via DHCP. (F0036879)
- Remote DMVS endpoint group call permissions are not enforced. (F0037101)
Known Defects/Issues in Version 2.620.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- Very rarely no audio is present on a DMVS MRD call. (F0035437)
bug fix release.
Features added in Version 2.610.4.0
- Added UI_CISCO_REGISTRATION_PERIOD to configure the initial Cisco SIP registration period.
Defects resolved in Version 2.610.4.0
- Prevent SIP SUBSCRIBE failure retries until the next successful registration with iCS. (F0036217)
Known Defects/Issues in Version 2.610.4.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- Very rarely no audio is present on DMVS MRD call. (F0035437)
Minor enhancements release.
Features added in Version 2.610.3.0
- Re-subscription to iCS halted when registration is lost.
Defects resolved in Version 2.610.3.0
Known Defects/Issues in Version 2.610.3.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- Very rarely no audio is present on DMVS MRD call. (F0035437)
Bug fix release.
Features added in Version 2.610.2.0
Defects resolved in Version 2.610.2.0
- The DSP status log is not included in the TechSupport logs when initiated from iManager. (F0036123)
- SE708 drops a Cisco call after about 70 to 90 seconds, iCS telephony is ok. (F0036146)
Known Defects/Issues in Version 2.610.2.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- Very rarely no audio is present on DMVS MRD call. (F0035437)
Minor enhancements release.
Features added in Version 2.610.1.0
- Remove security vulnerability CVE-2002-0510.
- Configuration of the 'SbRTP lost' timeout.
- Support for configuration of various SIP registration timers.
Defects resolved in Version 2.610.1.0
- SE708 will act oddly if you dial its own (ICS SIP) number; this and subsequent calls will fail until a timeout expires. (F0035836)
- SE708 crashes if the Intercom appearance number is same as its Cisco appearance number and it receives a call from Cisco 11.5. (F0035771)
- SE708 changes the voice recorder stream when the call becomes active. (F0035821)
Known Defects/Issues in Version 2.610.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- Very rarely no audio is present on DMVS MRD call. (F0035437)
Bug fix release.
Features added in Version 2.600.8.0
- SIP missed re-invite timeout changed to match iD808 for iCS failure scenarios.
Defects resolved in Version 2.600.8.0
- Originator or talking group calls do not correctly stack higher priority incoming group calls. (F0035301)
- iCS loses registration with remote SE708, causing incoming calls to fail with 'User not found'. SE708 reports registration Ok. (F0035288)
- An iCS failure when the SE708 has a SIP call active can cause the SE708 to reset. (F0035308)
- Local answerback call answered by iD712/SE708 not recognised by originator. (F0035347)
- Possible crash when an active P2P call is backgrounded by a higher priority Group call. (F0035381)
Known Defects/Issues in Version 2.600.8.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes its possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- Very rarely no audio is present on DMVS MRD call. (F0035437)
Bug fix release. *Not formally released*
Features added in Version 2.600.7.0
Defects resolved in Version 2.600.7.0
- A remote originated answerback group call doesn`t time out and close after a number of seconds. (F0035294)
Known Defects/Issues in Version 2.600.7.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes it`s possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- iCS loses registration with remote SE708, causing incoming calls to fail with 'User not found'. SE708 reports registration Ok. (F0035288)
Bug fix release.
Features added in Version 2.600.6.0
- SE708 modified to match iCS changes required for F0035194 (The warble tone might not be heard when initiating a group call using DMVS).
Defects resolved in Version 2.600.6.0
- A group call of higher precedence does not take over a lower precedence group call on remote 708. (F0034791)
- A remote iD712 may drop a stacked point to point call when a higher priority group call has ended. (F0034798/F0034812)
- An intercom call can be made from a remote device to a local device with DMVS intercom disabled. (F0034861)
- The Voice Recorder RTP port allocation calculation has not been correctly updated for Willow, there could therefore be a RTP port conflict in a fully saturated unit. (F0034906)
- CDR events do not populate the to_name field with the line appearance number when the name is missing. (F0034939)
- The Voice Recorder RTP port allocation calculation has not been correctly updated for Willow. (F0034906)
- Incoming calls answered directly on handset initially use the default audio termination in CDR events before switching to HANDSET_1 when fully connected. (F0034940)
- Incoming calls answered directly on handset generate unnecessary audio stop & start events. (F0035043)
- Device GUI can freeze for 30 seconds when DNS resolution of Cisco PBX hostname fails. (F0035050)
- Devices reboot or lock up after overnight autoscript tests. (F0035162)
- Issues with group calls with privacy enabled on a remote device. (F0035164)
- Remote device can exit out of an incoming locked DMVS intercom group call. (F0035165)
- Remote device receiving a mix group call doesn't have the 'T to talk option'. (F0035166)
- Remote DMVS mixing group call shows connecting when connected. (F0035167 )
- Remote SE708s occasionally freeze/lockup when making or receiving multiple group calls. (F0035210 )
- Local only group call originating from a local SE708 device fails with "Call barred, call failed" or similar message. (F0035255)
- "Press * to answer" still exists for an answerback group call after the GC has been answered elsewhere and then cleared down. (F0035282)
Known Defects/Issues in Version 2.600.6.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes it`s possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
- One way audio for up to 15s after iCS failover. (F0034459)
- Remote SE708 does not see the group call when it`s dialled from an ID808 remote device when the DMVS intercom feature is enabled on the call region until a resync is applied. (F0034963)
- Remote device shows the intercom as out of service even when the DMVS intercom feature is enabled on the call region. (F0034945)
- iCS loses registration with remote SE708, causing incoming calls to fail with 'User not found'. SE708 reports registration Ok. (F0035288)
Bug fix release.
Features added in Version 2.600.5.0
Defects resolved in Version 2.600.5.0
- You cant Press * to answer DMVS intercom Answerback calls from a SE708 at a remote site. (F0034751)
- DMVS MRD and Hoot services are not brought into service from a SE708 at a remote site. (F0034753)
- A DMVS intercom Answerback calls originated from a remote SE708 does not fully connect when answered at a remote SE708. (F0034786)
Known Defects/Issues in Version 2.600.5.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes it`s possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
Bug fix release. *Not formally released*
Features added in Version 2.600.4.0
Defects resolved in Version 2.600.4.0
- You cant Press * to answer DMVS intercom Answerback calls from a SE708 at a remote site. (F0034751)
- DMVS MRD and Hoot services are not brought into service from a SE708 at a remote site. (F0034753)
Known Defects/Issues in Version 2.600.4.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes it`s possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
Bug fix release.
Features added in Version 2.600.3.0
Defects resolved in Version 2.600.3.0
- Prompt to answer an Answer-back call missing on remote devices. (F0034545)
- Wait for Answer-back fails for a DMVS call on remote devices. (F0034558)
Known Defects/Issues in Version 2.600.3.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes it`s possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
Bug fix release.
Features added in Version 2.600.2.0
Defects resolved in Version 2.600.2.0
- When an SE708 receives a remote DMVS Willow incoming standard group call, the call will initially correctly not display the Press * to talk prompt. After the call is active for a time, the Press * to talk prompt incorrectly appears on the screen. (F0034340)
- When an SE708 receives a remote DMVS Willow incoming mixing group call, and the T button is pressed, the call will appear to work correctly, but the audio cannot be heard at the other end. (F0034341)
- When making a DMVS intercom call from a far side unit, the local se708 shows splash screen incompatible audio parameters call failed' and call doesn't connect. (F0034350)
- No audio during a telephony call. (F0034357)
- A SE708 barged into an operational DMVS ARD shows as connecting when the originating user clears out of the DMVS ARD. (F0034360)
- Group call fails when initiated from a local SE708, local to far side unit (sb534), 'Incompatible audio parameters' appears on se708 splash screen. (F0034421)
- Local to remote group call doesn't connect. (F0034422)
- Can't answer DMVS intercom call initiated from a farside unit when intercom privacy is enabled on the receiving local SE708. (F0034439)
- No audio from DMVS intercom group call initiated from local to remote+local units. (F0034441)
Known Defects/Issues in Version 2.600.2.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
- Sometimes it`s possible to have a DMVS MRD show busy elsewhere if you press the speaker channel it`s assigned to fairly quickly if the channel is set to unlatched. (F0034362)
Project Willow release.
Features added in Version 2.600.1.0
- Support for DMVS Intercom & Group calls on a unit sited at a 'remote' location.
Defects resolved in Version 2.600.1.0
- Very rarely, SE708 can crash when handling multiple SIP transactions. (F0034236)
Known Defects/Issues in Version 2.600.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally lockup causing the unit to freeze until rebooted. (F0033401)
Bug fix release.
Features added in Version 2.500.4.0
Defects resolved in Version 2.500.4.0
- A bridged line appearance on a SE708 continued to ring after the call had been answered on another device (id808). (F0034122)
- When the talk/listen rights of a DMVS Hoot voice service on handset are changed the corresponding CDR talk/receive audio start/stop event are not generated. (F0034148)
Known Defects/Issues in Version 2.500.4.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally freeze, locking up the unit, when processing intensive Autoscript commands. (F0033401)
Bug fix release.
Features added in Version 2.500.3.0
Defects resolved in Version 2.500.3.0
- Voice Recorder 'info' messages are not always generated when some of the reported parameters change. (F0034067)
- Music-on-hold not heard on Cisco endpoints when the call is put on hold by SE708. (F0034068)
- If the "talk" permission of a currently talking DMVS Hoot call is removed, talk is not immediately disabled. (F0034073)
Known Defects/Issues in Version 2.500.3.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally freeze, locking up the unit, when processing intensive Autoscript commands. (F0033401)
Bug fix release.
Features added in Version 2.500.2.0
Defects resolved in Version 2.500.2.0
- Cisco PBX support unintentionally excluded from released code.
- Unsupported PBXs in the configuration can cause the SIP status icon to remain yellow, even though the PBX is ignored. (F0033994)
- The device can run out of media links when configured to use 3x VR streams when all speaker channels are populated. (F0034017)
Known Defects/Issues in Version 2.500.2.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally freeze, locking up the unit, when processing intensive Autoscript commands. (F0033401)
Cisco telephony support and 4:1 Voice Recorder.
Features added in Version 2.500.1.0
- Support for a single Cisco PBX for telephony (iCS is then used for Intercom & DMVS functionality); telephony features as per Version 2.400.1.0.
- Support for 3 Voice Recorder streams, with the ability to configure individual audio sources to be separately included in a stream or not.
- Change the default duration of the long-press action to � second (used for microphone mute, home page selection & wipe channel).
- OpenSSL and dropbear (SSH) libraries updated to fix potential security issues.
Defects resolved in Version 2.500.1.0
- Miscellaneous minor GUI bug fixes.
Known Defects/Issues in Version 2.500.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
- DSP can occasionally freeze, locking up the unit, when processing intensive Autoscript commands. (F0033401)
Bug fix release.
Features added in Version 2.400.6.0
Defects resolved in Version 2.400.6.0
- Telephony call with early media remains in far end ringing state until cleared. (F0033372)
Known Defects/Issues in Version 2.400.6.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
Bug fix release.
Features added in Version 2.400.5.0
Defects resolved in Version 2.400.5.0
- Telephony CDR call events are not consistent with P2P CDR operation for some handset/speaker transitions. (F0033250)
Known Defects/Issues in Version 2.400.5.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
Bug fix release.
Features added in Version 2.400.4.0
Defects resolved in Version 2.400.4.0
- Incoming telephony calls using a line instance other than 1 are still reported as using line 1 by SE708, causing iCS to generate incorrect call status information. (F0033180)
- When a call is initiated with a handset the Nice recorder doesn't record the call correctly. (F0033198)
Known Defects/Issues in Version 2.400.4.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
Bug fix release.
Features added in Version 2.400.3.0
Defects resolved in Version 2.400.3.0
- CDR heartbeat event generation can stop, causing the call details to not be recorded. (F0033103)
- The oldest stacked incoming call is not always presented to the user first when the device becomes idle. (F0033116)
- The SE708 iCMS status screen doesn't always show "Resync or logout required to fully implement changes. (F0033124)
- A DMVS ARD barge-in attempt from a �local� unit for a call at the talker limit is sometimes incorrectly connected by the local SE708. (F0033141)
- DSP crashes when stacked incoming telephone calls are answered & cleared in quick succession. (F0033148)
- When a speed dial is pressed which shares the same key as an active ARD the ARD will unlatch if tap-latch is enabled. (F0033156)
Known Defects/Issues in Version 2.400.3.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- DSP can occasionally crash when sent an audio configuration, e.g. after a user seats on the device. (F0033112)
Bug fix release.
Features added in Version 2.400.2.0
Defects resolved in Version 2.400.2.0
- tcpdump may sometimes fail to launch, or cause system problems on a loaded device. (F0032890)
- Incoming call pop-up can be partially overwritten by a changing background call register screen icon. (F0032932)
- When 2 people put a SbRTP ARD on hold at the same time or nearly the same time, the call drops. (F0032935)
- Dialling an Intercom number when a Telephony call is active briefly rings the remote end before the call is disallowed. (F0032950)
- Some CDR events such as INCOMING_AUDIO_START are not generated during telephony calls. (F0032988)
- Clearing an on-hold Telephone call does not drop the call. (F0033028)
- An outgoing group call can fail if the speaker key is pressed whilst the call is connecting. (F0033059)
- The Personal Directory search function stops working once the alternate tab view has been accessed. (F0033079)
Known Defects/Issues in Version 2.400.2.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
Features added in Version 2.400.1.0
Basic Telephony Support:
- Support for a limited number of PBX appearances, with 1 appearance active at a time.
- Default appearance used for outgoing telephone calls via a new Telephony splash screen.
- Telephony splash screen used for incoming telephone calls, with different actions to answer the call on the handset or speaker.
- Roll over for multiple incoming lines with 'other call notification'.
- Telephony calls added to call registers and to 'last connected number' redial.
- Telephone calls can be put on hold, allowing an iD808 to retrieve the call.
- DTMF support for connected Telephone calls when the splash screen is visible.
- Inbound and outbound number modification using the same rules as iD808.
- Fall-back to match earlier non-Telephony operation if Telephony is not configured.
- An Intercom and Telephone call cannot be active at the same time.
- Telephone calls have the same priority as Intercom calls on the unit.
- Note there is no support for Telephone directories in this release.
Defects resolved in Version 2.400.1.0
- Potential UI lockup due to multiple internal messages. (F0032689)
- Potential process hang when exiting. (F0032692)
- Moving a busy-elsewhere MRD voice service between speaker channels does not correctly restore the call state icon. (F0032883)
- Transient network/iCS issues may cause a unit to permanently fail to answer an Answerback call. (F0032909)
- A short DMVS MRD ring request does not always ring for the expected minimum duration. (F0032933)
Known Defects/Issues in Version 2.400.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- tcpdump may sometimes fail to launch, or cause system problems on a loaded device. (F0032890)
- Incoming call pop-up can be partially overwritten by a changing background call register screen icon. (F0032932)
- When 2 people put a SbRTP ARD on hold at the same time or nearly the same time, the call drops . (F0032935)
Enhancements release.
Features added in Version 2.320.2.0
- Extended the behaviour of the custom CDR protocol.
Defects resolved in Version 2.320.2.0
- Potential UI lockup (rare). (F0032689)
Known Defects/Issues in Version 2.320.2.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
Enhancements release.
Features added in Version 2.320.1.0
- Added a custom CDR protocol version to configure specific behaviour.
Defects resolved in Version 2.320.1.0
- Local call-forward settings may be lost due to background iCMS updates. (F0032299)
Known Defects/Issues in Version 2.320.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
Enhancements release.
Features added in Version 2.310.1.0
- Other call notification.
- Automatic Intercom call back.
- Intercom call forward.
Defects resolved in Version 2.310.1.0
- CDR Heartbeat events include calls that are configured as not recordable. (F0032128)
- Various MRD ringtone issues. (F0031399)
- Moving a call that is already talking on speaker to handset does not correctly illuminate the 'Tx' LED. (F0031488)
- Quiet Office mode handset output is not adjusted for acoustic shock protection. (F0031479)
- The SE708 Intercom screen does not update to show when an outgoing call is redirected, plus other related issues. (F0031912)
- Incorrect call details shown for an unstacked group call following an unsuccessful answerback answer attempt. (F0032057)
- The Intercom privacy and missed call icons should not be presented when device is not using intercom appearance. (F0032168)
Known Defects/Issues in Version 2.310.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
Bug fix release.
Features added in Version 2.300.4.0
Defects resolved in Version 2.300.4.0
- An answerback group call in progress is being dropped as the remote unit answers the call. (F0031038)
- When a DMVS ARD call is cleared remotely the channel status icon doesn't show the transitory clearing state.
Known Defects/Issues in Version 2.300.4.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
Enhancements release.
Features added in Version 2.300.3.0
- Change to allow iCMS to separately disable either Intercom or overall iCS operation using xml files.
- Auto Discovery enhanced to blank out the user name when the user is logged out.
Defects resolved in Version 2.300.3.0
Known Defects/Issues in Version 2.300.3.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
Bug fix release.
Features added in Version 2.300.2.0
Defects resolved in Version 2.300.2.0
- Local SE708 occasionally failed to show desired call status for a DMVS ARD call. (F0030599)
- Sometimes DMVS MRD call�s activity lamp is permanently lit up, although there isn�t any voice activity. (F0030600)
- Local/Remote endpoint is sending INCOMING_AUDIO_START CDR event for a private-elsewhere MRD call. (F0030637)
- Remote SE708 shows yellow SIP icon when registration with iCS fails; it should show red flashing icon to match iD808 (F0030634)
- ARD receive audio is not always muted when the ARD call is idle which can mean an Out-of-service tone from an iG330 is heard on an idle ARD, which does not match iD808. (F0030713)
- SIP status icon does not turn yellow to indicate a selected DMVS service is inactive. (F0030640)
- SIP status icon does not always indicate a DMVS subscription failure. (F0030714)
- Minor issues with call state reporting. (F0030768)
Known Defects/Issues in Version 2.300.2.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
Project Hawthorn release.
Features added in Version 2.300.1.0
- DMVS Private Wire calls supported, with IGMP auto-leave.
- Quiet Office support.
- Global Muting support added to Hoot calls.
- Configurable Ethernet MTU.
- Default RTP port range updated to better match other products.
- Handset mute state updates immediately to match PTT/PTM settings change. (NPD Fragment List ID 3).
- Engineering passwords update to match Chestnut.
- OpenSSL library updated to fix security issues.
Defects resolved in Version 2.300.1.0
- Muted speaker channels may be briefly heard at power-up/resync/login. (F0025825)
- The Intercom screen does not reflect a change in the seated user name until the device is restarted or the user reseated. (F0026314)
- Single digit IP addresses from iCMS converted to 0. (F0026404)
- SE708 does not exit the privacy state when a non-privacy-aware device cancels privacy by barging in to this previously private call. (F0028007)
- IGMP Join fails if attempted for more than 20 SbRTP links simultaneously. (F0028841)
- IGMP join request made for default MCC address when this is not required. (F0029063)
- An SNMP IP address greater than 11 characters is truncated. (F0029279)
- Initialisation issues when DHCP server timeout is set to 1 second. (F0029376)
- Possible crash if the device is repowered when creating configuration files. (F0029679)
- Some SIP rejection messages are not immediately handled, causing a delay in any response action. (F0029680)
- Boot time firmware downgrade to v1 image via down arrow is not possible on a small number of units (Firmware workaround solution). (F0030598)
- DSP: Specific IGMP membership query messages are not seen resulting in multicast not being received until the next general IGMP membership query. (F0029987)
- DSP: Actions taken to mitigate detected network audio loops can result in stuck voice services. (F0030050)
Known Defects/Issues in Version 2.300.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
CDR maintenance release.
Features added in Version 2.010.1.0
- FR 1775: Reduce Heartbeat CDR Event information.
Defects resolved in Version 2.010.1.0
- CDR Recording-Stream-Info events are generated in some cases where not strictly necessary. (F0024746)
Known Defects/Issues in Version 2.010.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- Muted speaker channels may be briefly heard at power-up/resync/login. (F0025825)
Bug fix maintenance release.
Features added in Version 2.001.1.0
Defects resolved in Version 2.001.1.0
- Occasional failure of the SIP stack to initialise due to a DNS interface initialisation error. (F0025365)
Known Defects/Issues in Version 2.001.1.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- CDR Recording-Stream-Info events are generated in some cases where not strictly necessary. (F0024746)
- Muted speaker channels may be briefly heard at power-up/resync/login. (F0025825)
Bug fixes following Validation.
Features added in Version 2.000.3.0
Defects resolved in Version 2.000.3.0
- Fixed: ARD calls can be unmuted by the user from states that should always have audio muted. (F0025875)
- Fixed: With P2P set to have highest priority, P2P calls do not override a group call when its precedence is set to zero. (F0025913)
- Fixed: The device information screen does not display the device MAC address as it does on the iD808. (F0025915)
- Fixed: When there is no iCS configured for a device, the devices status shows the SIP error icon flashing red and not registered rather than being grayed out. (F0025917)
- Fixed: There are a number of issues with moving a Voice Service to another speaker channel when the VS is not idle and/or unmuted. (F0025933)
- Fixed: If the iCMS icon is animating when the user logs out, then the icon may continue to animate until a user logs in. (F0026221)
Known Defects/Issues in Version 2.000.3.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- CDR Recording-Stream-Info events are generated in some cases where not strictly necessary. (F0024746)
- SE708v2 may also share iD808 defect F0025297, "Occasional failure of the SIP stack to initialise due to a DNS interface initialisation error". (F0025365)
- Muted speaker channels may be briefly heard at power-up/resync/login. (F0025825)
Bug fixes following Validation.
Features added in Version 2.000.2.0
- Change hoot listen-only icon.
- Change top-level menu screens to 'tab' style instead of arrows to indicate further screens.
- Change personal directory screen to use 'tab' style with overlaid icon to indicate alternate Group or P2P entry view.
- Make individual channel mute states persistent with overall menu mute-all action.
- Add descriptions for additional SIP call failure codes.
Defects resolved in Version 2.000.2.0
- Fixed: The suppressed ringtone during incoming ring with ring-on-busy disabled is not restored if the active call is cleared while it is still ringing. (F0024734))
- Fixed: If multiple ARD calls are simultaneously dropped the call state icons may not be updated. (F0025168)
- Fixed: A 'sync without reset' from iCMS may not update 'unavailable' entries in the speed-dial screens. (F0025211/F0025400)
- Fixed: Live updates of the Group XML file are not handled correctly for group-type entries in the Personal directory. (F0025212)
- Added: Diagnostic 'network trace' now automatically disabled when iCMS 'log upload' command processed. (F0025210)
- Fixed: Call register match operation may not find correct entry with strings that contain ligatures. (F0025499)
- Fixed: A mixing group call stays in a connecting state on the chair device. (F0025500)
- Fixed: Intercom screen for Group calls shows chairperson's dial number rather than Group call number. (F0025603)
- Fixed: Incompatible values used for Ring On Busy from iCMS. (F0025767)
- Fixed: The microphone audio is not sent to the VR when a user talks on a hoot configured as not-recorded. (F0024737)
- Fixed: The microphone audio sent to the VR if there are multiple active streams is combined, potentially boosting the volume. (F0024737)
- Fixed: After displaying a personal directory view (e.g. P2P or Group) that has no entries, switching to the other view ignores the ok (dial) key. (F0025829)
- Fixed: iCMS change from manual to DNS resolving may be slow. (D69)
- Fixed: listen-only call on handset LED was orange.
- Fixed: Speaker key still acted on active voice-service call on handset when Intercom screen is displayed.
- U-Boot bootloader changed to update its environment variables to include the paths that match the readme.
- Workaround: The slowly flashing 'Intercom Active' banner has occasionally been seen to flash rapidly. (F0024745)
- Change to increase Logon timeout for iCMS to 40 seconds to allow for processing delays with very large directories.
Known Defects/Issues in Version 2.000.2.0
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- CDR Recording-Stream-Info events are generated in some cases where not strictly necessary. (F0024746)
- SE708v2 may also share iD808 defect F0025297, "Occasional failure of the SIP stack to initialise due to a DNS interface initialisation error". (F0025365)
- Muted speaker channels may be briefly heard at power-up/resync/login. (F0025825)
This is the first release of SE708v2 firmware and contains the following features.
SE708 Features
- Provides an iCS based IP Intercom with support for 8 simultaneous Hoot, ARD or MRD voice services and separate P2P and Group intercom calls.
- Supports user selectable P2P call autoanswer (privacy).
- Supports ARD/MRD privacy & global-muting.
- Supports local-muting and ring-on-busy functionality.
- Supports call priority to allow a higher priority intercom call to replace the active call.
- Supports standard, mixing, answerback and locked Group calls, including talk-only operation.
- Supports stacked Group calls so that a lower priority Group call is stored and accepted when allowed.
- Supports global, personal, group and location intercom call directories.
- Supports 4 pages of intercom Speed-dials.
- Supports call register for missed, received and placed intercom calls.
- Supports Voice Recorder stream and CDR event generation with secondary stream support.
- Supports gooseneck, open-mic and handset (with configurable acoustic-shock protection) operation. Gooseneck / open-mic detected and selected automatically.
- Supports configuration and upgrade via iCMS.
- Supports configuration via GUI.
- GUI uses new simplified icons and colour scheme.
- Supports the Autodiscovery protocol.
- Supports limited read-only SNMP.
- Provides a single Ethernet connection with DHCP or manual network configuration.
- Supports primary and secondary NTP and DNS servers via manual or DHCP configuration.
- Supports primary and secondary iCMS servers via manual, DHCP or DNS configuration.
- Provides an RS232 serial port for diagnostics and configuration in a similar manner to other i-series units.
- Supports secure engineering access via SSH for diagnostic purposes.
- Supports a technical support 'send-logs' facility.
- Supports a basic 'recovery mode' for units that have failed in the field.
- Supports engineering tools for basic network and audio hardware diagnostic purposes.
- Uses encrypted and authenticated upgrade image files for unit security.
Known Defects/Issues in Version 2.000.1.0
- The changes requested to overall/individual channel muting are not included in this build.
- The suppressed ringtone during incoming ring with ring-on-busy disabled is not restored if the active call is cleared while it is still ringing. (F0024734))
- A restart is required to fully apply an IP address change, this can occur if a delayed DHCP exchange occurs after a temporary fallback IP address has been adopted by the unit (common to most i-Series products). (F0024735)
- Changing the Ethernet port mode to non-auto modes can cause the DSP firmware to crash. (F0024736)
- The microphone audio is not sent to the VR when a user talks on a hoot configured as not-recorded. (F0024737)
- The microphone audio sent to the VR if there are multiple active streams is combined, potentially boosting the volume. (F0024737)
- The slowly flashing 'Intercom Active' banner has occasionally been seen to flash rapidly. (F0024745)
- CDR Recording-Stream-Info events are generated in some cases where not strictly necessary. (F0024746)
Back
to the Home Page